Printable List of Tools and Materials for Garage Organization

Organize, cut the clutter and tools, clean up the workbench and garage floor.

Advertisement
 

Rotating Storage Shelves

Cutting List
A - Wide divider, 3/4" x 24" x 54"

 

B - Two narrow dividers, 3/4" x 11-5/8" x 54"

C - Bin bottom, 3/4" x 24" diameter

D - Up to 16 shelves, 3/4" x 11-5/8" x 11-5/8"

E - Base, 3/4" x 24" x 24"

G - Two treated 1x2s, 1 x 2 x 24"

H - Top shelf, 3/4" x 18" x 18"

J - Shelf side, 3/4" x 7-1/2" x 18"

K - Shelf side, 3/4" x 7-1/2" x 17-1/4"

Materials List

  • One and a half 4x8 sheets of(birch) plywood

  • One 12" round lazy Susan ring

  • One 3" square lazy Susan ring

  • 1 lb. of 2" No. 8 screws

  • Sixteen 3/4-in. No. 6 flat head screws

  • Ten 4' strips of 3" vinyl base

  • 1 lb. of 1" tacks

  • One tube of vinyl base adhesive

  • Two 2' treated 1x2s

  • Three 2-1/2" x 3/16" masonry screws

  • Eight 2-1/2" screws

 

Pet Food Dispenser

Cutting List Two 1x8 x 18-1/4"—bin bottom and shelf

 

Two 1x8 x 40-3/4"—outer sides Note: Cut a 45-degree angle on one end set in 2” from the edge

Three 1x6 x 29"—inner sides and divider Note: Cut a 45-degree angle on one end set in 1” from the edge.

One 1x12 x 21-1/4"—lid and top

Note: Rip it to 22-1/2 degrees set 2" in from the edge. 2" is the narrow side.

One 1/4" x 29" x 18-1/4"—hardboard back

One 1x6 x 18-1/4"—mounting cleat Note: Rip in half at 45 degrees

One 1x2 x 18-1/4"—back brace

Two 1x1 x 8"—front cleats

Materials

  • One 10' length of 1x8 aspen
  • One 9' length of 1x6 aspen
  • One 2' length of 1x12 aspen
  • One 2' length of 1x2 aspen
  • One 2' length of 1x1 aspen
  • 1-3/4" x 8' quarter round or shelf molding
  • 1-1/4" x 2' x 4' tempered hardboard
  • One 18" x24" x.093" acrylic sheet
  • One 24" piano hinge
  • Two 4" dia. blast gates
  • 1 lb. of 2-1/4" trim head screws
  • 1 lb. of 1-1/4" screws
  • Eight 1" No. 6 flat head wood screws
  • Four 2-1/2" screws
  • Sixteen 3d finish nails
Peg Board Cabinets

Cutting List
1/4" Peg-Board panels (three 24" x 31-1/2", two 23" x 31-1/2") 1x2 spacers, 1x6 cleat, 1x6, 1x8 and 1x2 frames —measure and cut to fit around panels.

 

Materials List

  • One 4'x8' sheet of 1/4-in. Peg-Board Five

  • 10' lengths of 1x2 poplar

  • Two 10' lengths of 1x6 poplar

  • One 3' length of 1x8 poplar

  • One 6' piano hinge

  • One lockable hasp

  • 1 lb. of 2" finish nails

  • 1 lb. of 1" screws

  • Eight 3" screws

 

From The Family Handyman - September 2002
Originally in Organize Your Garage: Three Storage Projects
 
Copyright ©2005 Home Service Publications, Inc. All rights reserved. Unauthorized reproduction, in any manner, is prohibited.
Must Read Should Everyone Read This? Yes! I vote for this story
Share Your Comments
 
Remaining Character Count:
 
See All Comments

Advertisement
 
Related Links

Advertisement
Popular stories from the source site rd.com sorted by diggs