From About This Project
Don’t melt down if a doorknob, misguided chair or an impromptu hockey game knocks a big hole in your wall. With a little patience, even a novice can complete a near-invisible repair. While the total time commitment isn’t great, the process stretches over three to four days to allow coats of drywall compound and paint to dry.
Before cutting out the damaged area, check the wall for obstructions. Often you’ll find a wire, pipe or duct. If so, work carefully around them with a drywall or keyhole saw. Or make a shallow cut by repeatedly scoring the line with a sharp utility knife.
It’s easier to add backer board than to try to cut the drywall over studs. Cut the backer boards about 4 in. longer than the height of the hole. Pine or other soft wood works well. Hold them tight to the backside of the drywall when fastening them. Hold the boards carefully so the screw points won’t prick your fingers if they pop out the backside. The drywall screws will draw the boards in tight. Sink the screwheads slightly below the drywall surface.
Measure the thickness of the drywall (most likely 1/2 in.), and look for a large enough scrap from a damaged piece at a home center, rather than buy a full 4 x 8-ft. sheet. Cut it to size and screw it into place, spacing the screws every 6 in.
Taping the edges of the patch to make it invisible is the trickiest part of the job. Buy a gallon tub of drywall compound ($4) and a roll of paper tape ($1.50). You can use mesh tape, but it isn’t as strong. If you have a lot of repairs, also buy a sack of 20-minute setting compound ($5 a bag). It hardens quickly and doesn’t shrink, so it’s ideal for filling cracks and gaps before applying the joint tape. For smoothest results, also pick up flexible 6- and 10-in. taping knives ($7 each).
Apply a coat of compound and tape to each joint. Thin the compound a bit with water to help embed the tape. Smooth the tape with the 6-in. knife, pulling out from the center toward each end. Squeeze some, but not all, of the compound out from under the tape so you don’t create a big hump on the wall. Immediately apply a light coating to the topside of the tape, tapering it out onto the wall.
The second and third coats are to blend and smooth the taped joints so they’ll be invisible when painted. After each coat is dry, set a straightedge against the wall to check for obvious dips and bumps. Knock off bumps and ridges with your taping knife. Add more coats as needed. Then sand, prime and paint.
How To Repair Holes in Drywall
Large Holes
20-Minute Setting Compound: Twenty-minute setting compound is a great product for filling deep holes and gaps and for your first taping coat because, unlike regular joint compound, it hardens quickly without shrinking. That means less time spent filling. And you can apply a second coat of compound as soon as the first hardens. You don’t have to wait for it to dry completely.
For most uses, buy the lightweight type. It comes as a powder in sacks ($5 for 18 lbs.). Mix only what you can use in about 10 minutes. It hardens quickly, often in your pan if you’re too slow! Completely clean your pan and knife before mixing a new batch. Otherwise it’ll harden even faster! To avoid clogging the sink drain, throw leftover compound into the trash.
Small Holes
Small holes caused by screws or hooks, wall fasteners or drywall fasteners that pop up are simple to repair, but again time consuming because you almost always have to repaint the walls. Nail pops are common and particularly irritating, because you’re likely to have more than one. But drywall screws sometimes pop up too, as a result of damp framing that dries out and shrinks during the first year or two in new construction.
The first step of the fix is to drive nails back down using a nail set. If you have screws, dig the drywall compound from their heads with a utility knife and turn them in tight with a screwdriver.
Then dimple the hole slightly concave with a hammer to indent any raised edges. But take care not to crush the drywall core. In addition, cut away any paper tears with a sharp utility knife. This is a good technique to use with old wall fasteners as well. It’s usually easier to tap them into the wall slightly rather than pull them out.
Two coats of drywall compound, applied with two swipes of the knife in an “+” pattern, should fill the holes. The first coat will shrink a bit, leaving a slightly smaller dent to be filled by the second coat. Scrape the excess off the surrounding wall so you don’t build up a hump. Sand lightly to blend with the surrounding wall.
Be sure to prime the spot. Otherwise the topcoat will absorb into the patch and make the area look different from the surrounding paint. And use a roller when priming to help raise the surface texture to match the surrounding wall.
Cracked Corners
Every home settles unevenly as it ages. This sometimes causes inside corners to crack or ripple. Often the crack will run from floor to ceiling. Once you spot this problem, watch it for two to three months for continued movement and fix it after all movement stops.
The key to renewing the strength of the corner is to remove all loose tape and drywall compound. If the drywall below has crumbled, cut it away with your utility knife and fill the gap with setting compound.
Retape the joint following the techniques shown. Crease the paper tape down the middle so it fits into the corner easily.
It’s difficult to spread compound smoothly on one side of the corner without marring the other side. The trick is to apply compound for the second and third coats only on one side at a time. Let the one side dry, then do the other side.
Finally, buy a fine-grit sanding sponge ($3) to smooth the corners. It’ll do a nice job without gouging.
I agree with Marv, need advice on a lightly textured walls that are very common in Ohio. I'ts impossible to fix a nail or anchor 'hole' on the wall as the texture never matches.
Never see these articles discuss repairs on textured walls... They are very common in Oklahoma. How about covering this version of interior walls.
A better way to fix large holes in sheetrock is to square up the hole. Cut a piece of sheetrock 1 in wider all around then the hole. On the back side of the patch, cut away the one inch border leaving the face paper intact using score and snap. Ligtly sand the back of the exposed face paper and apply a thin coat of fast set compound to the paper and the edges of the patch. Apply a coat to the inside edges of the hole and install the patch smoothing the edge down with a 6 " knife DON'T OVERWORK.