From About This Project
Replace a Dead Motor
If your bathroom fan is dead, here’s some
good news: You don’t have to tear out the entire unit. Even if your fan is decades old, chances are you can get a replacement motor. Although a new motor costs about the same as a new fan, replacement saves time and trouble. You don’t have to cut into the ceiling, crawl around your attic or get up on your roof. It usually takes less than an hour.
Your first step is to get the fan’s model number. Remove the fan grille and vacuum away the dust to find the number on a label or stamped on the fan’s housing. But don’t order a new motor until you remove the old one. You might need other parts too.
Bath fans vary in design, but motor replacement requires the same basic steps, no matter which brand or model you have. Turn off the power to the fan at the main breaker panel. Then unplug the fan and remove the motor plate. Some motor plates are released by pressing or prying on the side of the fan housing. Others are secured with a screw or two.
Before you can remove the motor from the plate, you have to get the blower off the motor’s shaft. This is often the toughest part of the whole project. An older metal blower might be fastened with a screw. Plastic blowers usually aren’t fastened at all, but simply slide off the shaft. Either way, removal may require some hard prying and pulling. If you wreck the blower while removing it, don’t worry. You can order a replacement for $3 to $10. To install the new motor, simply reverse the process.
CAUTION: Turn power off at the main panel before starting any work.
Run Duct Outside to Prevent Roof Rot
When there’s an attic above the bathroom, some installers take a shortcut: Instead of running the duct through the roof,
they end the duct inside the attic. The result is that the fan fills the attic with moist air. That moisture feeds wood rot. In winter, frost forms in the attic and as the frost melts, water can damage the ceilings below.
If you don’t have a cap on your roof, chances are your bath fan vents into the attic. Running a new duct up through the roof isn’t a complex job, but you will have to work in the attic and on the roof. Since you’re doing all that work anyway, consider replacing the fan.
An attic can get dangerously hot in summer, so work on a cool day. Wear a dust mask and eye protection. Bring a trouble light and a large scrap of plywood to use as a work platform.
Here’s how to do the job with only two trips to the attic: On your first trip, measure the exhaust port diameter and pick a spot near the fan where you want the duct to exit the roof. Drive a screw up through the roof so you can find the location from outside. Then head for a home center. Here’s what you’ll need:
A roof vent cap ($14).
Aluminum duct the same size as the flexible duct ($4).You only need about 6 in., so buy the shortest section available and cut it with a metal snips.
Two 6-in. hose clamps ($4).
One tube of roofing cement ($3).
Roofing nails and 1/2-in. sheet metal screws.
Flexible, insulated duct ($15). Insulation prevents condensation from forming on or inside the duct. Home centers often carry only 4-in. insulated duct. If your fan has a 3-in. port, you can still use 4-in. duct by attaching a 3-in. elbow ($2) and a 3 x 4-in. reducer ($5) with sheet metal screws.
Install the roof vent cap.
How to Repair a Broken Bathroom Fan-running a new duct to the roof cont'd
Working On The Roof
Your roof may not look intimidating from the ground, but it will seem a lot higher and steeper when you climb on it. So don’t take on this project unless you feel safe and secure up there. Wear soft-soled shoes for good traction, make sure the roof is dry and stay clear of power lines. For increased safety, buy roof jacks at a home center ($15 per pair). These metal brackets support a plank that keeps you and your tools on the roof. For the ultimate in safety gear, rent a roof harness
($35 per day). The harness connects to a rope that’s anchored to the roof.
Parts For Bath Fans
If your fan was made by one of the major manufacturers below, your chances of finding replacement parts are good. Fan motors cost about the same as entire fans of comparable quality. The motor for an inexpensive fan, for example, might cost $15, while a motor
for a top-of-the-line fan can cost more than $100. If your fan’s grille is cracked, corroded or yellowed, you can replace it, too, for $3 to $10.
Air King: Order parts by calling: (U.S.) 877-304-3785; (Canada) 800-465-7300.
Broan, Nutone, Nautilus: To view fan diagrams and installation guides, visit www.broan.com. To find a local parts supplier or to order parts directly, call 800-558-1711. In Canada, call 877-896-1119.
Panasonic: To view fan diagrams and installation guides, visit www.panasonic.com. To order parts, call 800-833-9626.
Where's the rest of this? How to deal with shingles, attaching the cap and sealing it were left out. Not to mention the whole cutting through the roof itself bit.